/*********************************************************************
*
* Hardware specific definitions
*
*********************************************************************
* FileName: HardwareProfile_xxx.h
* Dependencies: None
* Processor: PIC24F, PIC24H, dsPIC, PIC32
* Compiler: Microchip C32 v1.00 or higher
* Microchip C30 v3.01 or higher
* Company: Microchip Technology, Inc.
*
* Software License Agreement
*
* Copyright © 2002-2009 Microchip Technology Inc. All rights
* reserved.
*
* Microchip licenses to you the right to use, modify, copy, and
* distribute:
* (i) the Software when embedded on a Microchip microcontroller or
* digital signal controller product (“Device”) which is
* integrated into Licensee’s product; or
* (ii) ONLY the Software driver source files ENC28J60.c and
* ENC28J60.h ported to a non-Microchip device used in
* conjunction with a Microchip ethernet controller for the
* sole purpose of interfacing with the ethernet controller.
*
* You should refer to the license agreement accompanying this
* Software for additional information regarding your rights and
* obligations.
*
* THE SOFTWARE AND DOCUMENTATION ARE PROVIDED “AS IS” WITHOUT
* WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING WITHOUT
* LIMITATION, ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR A
* PARTICULAR PURPOSE, TITLE AND NON-INFRINGEMENT. IN NO EVENT SHALL
* MICROCHIP BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT OR
* CONSEQUENTIAL DAMAGES, LOST PROFITS OR LOST DATA, COST OF
* PROCUREMENT OF SUBSTITUTE GOODS, TECHNOLOGY OR SERVICES, ANY CLAIMS
* BY THIRD PARTIES (INCLUDING BUT NOT LIMITED TO ANY DEFENSE
* THEREOF), ANY CLAIMS FOR INDEMNITY OR CONTRIBUTION, OR OTHER
* SIMILAR COSTS, WHETHER ASSERTED ON THE BASIS OF CONTRACT, TORT
* (INCLUDING NEGLIGENCE), BREACH OF WARRANTY, OR OTHERWISE.
*
*
* Author Date Comment
*~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
* Howard Schlunder 10/03/06 Original, copied from Compiler.h
* Jayanth Murthy 06/25/09 dsPIC & PIC24H support
* Pradeep Budagutta 15 Sep 2009 Added PIC24FJ256DA210 Development Board Support
* PAT 04/07/10 Removed GRAPHICS_HARDWARE_PLATFORM
* Added MMB support
********************************************************************/
#ifndef __HARDWARE_PROFILE_H
#define __HARDWARE_PROFILE_H
/*********************************************************************
* GetSystemClock() returns system clock frequency.
*
* GetPeripheralClock() returns peripheral clock frequency.
*
* GetInstructionClock() returns instruction clock frequency.
*
********************************************************************/
/*********************************************************************
* Macro: #define GetSystemClock()
*
* Overview: This macro returns the system clock frequency in Hertz.
* * value is 8 MHz x 4 PLL for PIC24
* * value is 8 MHz/2 x 18 PLL for PIC32
*
********************************************************************/
#if defined(__PIC24F__)
#define GetSystemClock() (32000000ul)
#elif defined(__PIC32MX__)
#define GetSystemClock() (80000000ul)
#elif defined(__dsPIC33F__) || defined(__PIC24H__)
#define GetSystemClock() (80000000ul)
#endif
/*********************************************************************
* Macro: #define GetPeripheralClock()
*
* Overview: This macro returns the peripheral clock frequency
* used in Hertz.
* * value for PIC24 is (GetSystemClock()/2)
* * value for PIC32 is (GetSystemClock()/(1<
*
********************************************************************/
#if defined(__PIC24F__) || defined(__PIC24H__) || defined(__dsPIC33F__)
#define GetPeripheralClock() (GetSystemClock() / 2)
#elif defined(__PIC32MX__)
#define GetPeripheralClock() (GetSystemClock() / (1 << OSCCONbits.PBDIV))
#endif
/*********************************************************************
* Macro: #define GetInstructionClock()
*
* Overview: This macro returns instruction clock frequency
* used in Hertz.
* * value for PIC24 is (GetSystemClock()/2)
* * value for PIC32 is (GetSystemClock())
*
********************************************************************/
#if defined(__PIC24F__) || defined(__PIC24H__) || defined(__dsPIC33F__)
#define GetInstructionClock() (GetSystemClock() / 2)
#elif defined(__PIC32MX__)
#define GetInstructionClock() (GetSystemClock())
#endif
/*********************************************************************
* UART SETTINGS
*********************************************************************/
#define BAUDRATE2 115200UL
#define BRG_DIV2 4
#define BRGH2 1
/* ################################################################## */
/*********************************************************************
* START OF GRAPHICS RELATED MACROS
********************************************************************/
/* ################################################################## */
/*********************************************************************
* AUTO GENERATED CODE
********************************************************************/
//Auto Generated Code
#define GFX_PICTAIL_V3
#define EXPLORER_16
#define USE_8BIT_PMP
#define PIC32_GP_SK_DM320001
#define DISPLAY_CONTROLLER SSD1926
#define DISPLAY_PANEL TFT_G240320LTSW_118W_E
#define COLOR_DEPTH 16
//End Auto Generated Code
/*********************************************************************
* END OF AUTO GENERATED CODE
********************************************************************/
#ifdef _GRAPHICS_H
/*********************************************************************
* ERROR CHECKING
*********************************************************************/
#if !defined (GFX_PICTAIL_V3) && !defined (GFX_PICTAIL_V2) && !defined (PIC24FJ256DA210_DEV_BOARD) && !defined(MULTI_MEDIA_BOARD_DM00123)
#error "Error: Graphics Hardware Platform is not defined! One of the three (GFX_PICTAIL_V3, GFX_PICTAIL_V2, PIC24FJ256DA210_DEV_BOARD) must be defined.
#endif
#if defined (__PIC24FJ128GA010__) || defined (__PIC24FJ256GA110__) || \
defined (__PIC24FJ256GB110__) || defined (__dsPIC33F__) || \
defined (__PIC24HJ128GP504__)
#if defined (USE_16BIT_PMP)
#error "The device selected does not support 16 bit PMP interface."
#endif
#endif
#ifndef DISPLAY_CONTROLLER
#error "Error: DISPLAY_CONTROLLER not defined"
#endif
#if (defined (GFX_PICTAIL_V3) || defined (PIC24FJ256DA210_DEV_BOARD)) && !defined(DISPLAY_PANEL)
#error "Error: DISPLAY_PANEL not defined"
#endif
/*********************************************************************
* SETTINGS FOR DISPLAY DRIVER FEATURE for PIC24FJ256DA210 Family of
* display controller
*********************************************************************/
#ifdef USE_DOUBLE_BUFFERING
#ifdef GFX_DISPLAY_BUFFER_START_ADDRESS
#undef GFX_DISPLAY_BUFFER_START_ADDRESS
volatile extern DWORD _drawbuffer;
#define GFX_DISPLAY_BUFFER_START_ADDRESS _drawbuffer
#endif
#define GFX_BUFFER1 0x00020000ul
#define GFX_BUFFER2 0x00050000ul
#endif
/*********************************************************************
* DISPLAY PARALLEL INTERFACE
*********************************************************************/
// EPMP is exclusive to GB210 devices and PMP to some devices
#if defined (__PIC24FJ256DA210__)
// EPMP is used by graphics controller
#elif defined (__PIC24FJ256GB210__)
#define USE_GFX_EPMP
#else
#define USE_GFX_PMP
#endif
/*********************************************************************
* DISPLAY SETTINGS
********************************************************************/
// -----------------------------------
// For SMART DISPLAYS
// -----------------------------------
// Using LGDP4531 Display Controller
#if (DISPLAY_CONTROLLER == LGDP4531)
#define DISP_ORIENTATION 90
#define DISP_HOR_RESOLUTION 240
#define DISP_VER_RESOLUTION 320
#define DISPLAY_PANEL -1
#endif // #if (DISPLAY_CONTROLLER == LGDP4531)
// Using S6D0129 Display Controller
#if (DISPLAY_CONTROLLER == S6D0129)
#define DISP_ORIENTATION 90
#define DISP_HOR_RESOLUTION 240
#define DISP_VER_RESOLUTION 320
#endif // #if (DISPLAY_CONTROLLER == S6D0129)
// -----------------------------------
// For SMART RGB GLASS
// -----------------------------------
// check if DISPLAY_PANEL is not defined set it to -1 to skip the rest
// of the display panel settings.
#if !defined (DISPLAY_PANEL)
#define DISPLAY_PANEL -1
#endif
// Using TFT_G240320LTSW_118W_E, TFT2N0369_E, DT032TFT_TS, DT032TFT Display Panel.
// These panels uses Solomon Systech SSD1289 as their controller.
#if (DISPLAY_PANEL == TFT_G240320LTSW_118W_E) || (DISPLAY_PANEL == TFT2N0369_E) || \
(DISPLAY_PANEL == DT032TFT_TS) || (DISPLAY_PANEL == DT032TFT)
/* note: For SSD1289
tHBP (horizontal back porch)= DISP_HOR_BACK_PORCH + DISP_HOR_PULSE_WIDTH
tVBP (vertical back porch) = DISP_VER_BACK_PORCH + DISP_VER_PULSE_WIDTH
Horizontal Cycle (280) = tHBP + DISP_HOR_FRONT_PORCH + DISP_HOR_RESOLUTION
Vertical Cycle (326) = tVBP + DISP_VER_FRONT_PORCH + DISP_VER_RESOLUTION
In summary, the DISP_HOR_PULSE_WIDTH should not exceed tHBP and
the DISP_VER_PULSE_WIDTH should not exceed tVBP. See SSD1289 data sheet for
details.
*/
#define DISP_ORIENTATION 90
#define DISP_HOR_RESOLUTION 240
#define DISP_VER_RESOLUTION 320
#define DISP_DATA_WIDTH 18
#define DISP_INV_LSHIFT
#define DISP_HOR_PULSE_WIDTH 25
#define DISP_HOR_BACK_PORCH 5
#define DISP_HOR_FRONT_PORCH 10
#define DISP_VER_PULSE_WIDTH 4
#define DISP_VER_BACK_PORCH 0
#define DISP_VER_FRONT_PORCH 2
#if (DISPLAY_CONTROLLER == MCHP_DA210)
#define GFX_LCD_TYPE GFX_LCD_TFT
#define GFX_DISPLAYENABLE_ENABLE
#define GFX_HSYNC_ENABLE
#define GFX_VSYNC_ENABLE
#define GFX_DISPLAYPOWER_ENABLE
#define GFX_CLOCK_POLARITY GFX_ACTIVE_HIGH
#define GFX_DISPLAYENABLE_POLARITY GFX_ACTIVE_HIGH
#define GFX_HSYNC_POLARITY GFX_ACTIVE_LOW
#define GFX_VSYNC_POLARITY GFX_ACTIVE_LOW
#define GFX_DISPLAYPOWER_POLARITY GFX_ACTIVE_HIGH
#endif
#endif // #if (DISPLAY_PANEL == TFT_G240320LTSW_118W_E) || (DISPLAY_PANEL == TFT2N0369_E) ||....
// Using TFT_G320240DTSW_69W_TP_E Display Panel
#if (DISPLAY_PANEL == TFT_G320240DTSW_69W_TP_E) || (DISPLAY_PANEL == _35QVW0T)
#define DISP_ORIENTATION 0
#define DISP_HOR_RESOLUTION 320
#define DISP_VER_RESOLUTION 240
#define DISP_DATA_WIDTH 18
#define DISP_HOR_PULSE_WIDTH 25
#define DISP_HOR_BACK_PORCH 8
#define DISP_HOR_FRONT_PORCH 8
#define DISP_VER_PULSE_WIDTH 8
#define DISP_VER_BACK_PORCH 7
#define DISP_VER_FRONT_PORCH 5
#endif // #if (DISPLAY_PANEL == TFT_G320240DTSW_69W_TP_E) || (DISPLAY_PANEL == _35QVW0T)
// Using PH480272T_005_I06Q Display Panel
#if (DISPLAY_PANEL == PH480272T_005_I06Q)
#define DISP_ORIENTATION 0
#define DISP_HOR_RESOLUTION 480
#define DISP_VER_RESOLUTION 272
#define DISP_DATA_WIDTH 24
#define DISP_HOR_PULSE_WIDTH 41
#define DISP_HOR_BACK_PORCH 2
#define DISP_HOR_FRONT_PORCH 2
#define DISP_VER_PULSE_WIDTH 10
#define DISP_VER_BACK_PORCH 2
#define DISP_VER_FRONT_PORCH 2
#if (DISPLAY_CONTROLLER == MCHP_DA210)
#define GFX_LCD_TYPE GFX_LCD_TFT
#define GFX_DISPLAYENABLE_ENABLE
#define GFX_HSYNC_ENABLE
#define GFX_VSYNC_ENABLE
#define GFX_DISPLAYPOWER_ENABLE
#define GFX_CLOCK_POLARITY GFX_ACTIVE_LOW
#define GFX_DISPLAYENABLE_POLARITY GFX_ACTIVE_HIGH
#define GFX_HSYNC_POLARITY GFX_ACTIVE_LOW
#define GFX_VSYNC_POLARITY GFX_ACTIVE_LOW
#define GFX_DISPLAYPOWER_POLARITY GFX_ACTIVE_HIGH
#endif
#endif // #if (DISPLAY_PANEL == PH480272T_005_I06Q)
// Using PH480272T_005_I11Q Display Panel
#if (DISPLAY_PANEL == PH480272T_005_I11Q)
#define DISP_ORIENTATION 0
#define DISP_HOR_RESOLUTION 480
#define DISP_VER_RESOLUTION 272
#define DISP_DATA_WIDTH 24
#define DISP_HOR_PULSE_WIDTH 41
#define DISP_HOR_BACK_PORCH 2
#define DISP_HOR_FRONT_PORCH 2
#define DISP_VER_PULSE_WIDTH 10
#define DISP_VER_BACK_PORCH 2
#define DISP_VER_FRONT_PORCH 2
#if (DISPLAY_CONTROLLER == MCHP_DA210)
#define GFX_LCD_TYPE GFX_LCD_TFT
#define GFX_DISPLAYENABLE_ENABLE
#define GFX_HSYNC_ENABLE
#define GFX_VSYNC_ENABLE
#define GFX_DISPLAYPOWER_ENABLE
#define GFX_CLOCK_POLARITY GFX_ACTIVE_LOW
#define GFX_DISPLAYENABLE_POLARITY GFX_ACTIVE_HIGH
#define GFX_HSYNC_POLARITY GFX_ACTIVE_LOW
#define GFX_VSYNC_POLARITY GFX_ACTIVE_LOW
#define GFX_DISPLAYPOWER_POLARITY GFX_ACTIVE_HIGH
#endif
#endif // #if (DISPLAY_PANEL == PH480272T_005_I11Q)
/* &&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&
&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&& */
/*********************************************************************
* IOS FOR THE DISPLAY CONTROLLER
*********************************************************************/
#if defined (GFX_PICTAIL_V1)
// Definitions for reset pin
#define RST_TRIS_BIT TRISCbits.TRISC1
#define RST_LAT_BIT LATCbits.LATC1
// Definitions for RS pin
#define RS_TRIS_BIT TRISBbits.TRISB15
#define RS_LAT_BIT LATBbits.LATB15
// Definitions for CS pin
#define CS_TRIS_BIT TRISDbits.TRISD8
#define CS_LAT_BIT LATDbits.LATD8
// Definitions for FLASH CS pin
#define CS_FLASH_LAT_BIT LATDbits.LATD9
#define CS_FLASH_TRIS_BIT TRISDbits.TRISD9
#elif defined (GFX_PICTAIL_V2)
#if (DISPLAY_CONTROLLER == LGDP4531)
#if defined(__dsPIC33FJ128GP804__) || defined(__PIC24HJ128GP504__)
// Definitions for reset pin
#define RST_TRIS_BIT TRISAbits.TRISA4
#define RST_LAT_BIT LATAbits.LATA4
// Definitions for RS pin
#define RS_TRIS_BIT TRISAbits.TRISA1
#define RS_LAT_BIT LATAbits.LATA1
// Definitions for CS pin
#define CS_TRIS_BIT TRISBbits.TRISB15
#define CS_LAT_BIT LATBbits.LATB15
// Definitions for FLASH CS pin
#define CS_FLASH_LAT_BIT LATAbits.LATA8
#define CS_FLASH_TRIS_BIT TRISAbits.TRISA8
// Definitions for POWER ON pin
#define POWERON_LAT_BIT LATAbits.LATA10
#define POWERON_TRIS_BIT TRISAbits.TRISA10
#else
// Definitions for reset pin
#define RST_TRIS_BIT TRISCbits.TRISC1
#define RST_LAT_BIT LATCbits.LATC1
// Definitions for RS pin
#define RS_TRIS_BIT TRISCbits.TRISC2
#define RS_LAT_BIT LATCbits.LATC2
// Definitions for CS pin
#define CS_TRIS_BIT TRISDbits.TRISD10
#define CS_LAT_BIT LATDbits.LATD10
// Definitions for FLASH CS pin
#define CS_FLASH_LAT_BIT LATDbits.LATD1
#define CS_FLASH_TRIS_BIT TRISDbits.TRISD1
// Definitions for POWER ON pin
#define POWERON_LAT_BIT LATCbits.LATC3
#define POWERON_TRIS_BIT TRISCbits.TRISC3
#endif
#elif (DISPLAY_CONTROLLER == SSD1906)
// Definitions for reset line
#define RST_TRIS_BIT TRISCbits.TRISC1
#define RST_LAT_BIT LATCbits.LATC1
// Definitions for RS line
#define RS_TRIS_BIT TRISCbits.TRISC2
#define RS_LAT_BIT LATCbits.LATC2
// Definitions for CS line
#define CS_TRIS_BIT TRISDbits.TRISD10
#define CS_LAT_BIT LATDbits.LATD10
// Definitions for A0 line
#define A0_LAT_BIT LATDbits.LATD3
#define A0_TRIS_BIT TRISDbits.TRISD3
// Definitions for A17 line
#define A17_LAT_BIT LATGbits.LATG14
#define A17_TRIS_BIT TRISGbits.TRISG14
#else
#error GRAPHICS CONTROLLER IS NOT SUPPORTED
#endif // (DISPLAY_CONTROLLER == ...
#elif defined (GFX_PICTAIL_V3)
#if defined(__dsPIC33FJ128GP804__) || defined(__PIC24HJ128GP504__)
// Definitions for reset pin
#define RST_TRIS_BIT TRISAbits.TRISA4
#define RST_LAT_BIT LATAbits.LATA4
// Definitions for RS pin
#define RS_TRIS_BIT TRISAbits.TRISA1
#define RS_LAT_BIT LATAbits.LATA1
// Definitions for CS pin
#define CS_TRIS_BIT TRISBbits.TRISB15
#define CS_LAT_BIT LATBbits.LATB15
#else
// Definitions for reset line
#define RST_TRIS_BIT TRISCbits.TRISC1
#define RST_LAT_BIT LATCbits.LATC1
// Definitions for RS line
#define RS_TRIS_BIT TRISCbits.TRISC2
#define RS_LAT_BIT LATCbits.LATC2
// Definitions for CS line
#define CS_TRIS_BIT TRISDbits.TRISD10
#define CS_LAT_BIT LATDbits.LATD10
#endif
#elif defined (MULTI_MEDIA_BOARD_DM00123)
// Definitions for reset line
#define RST_TRIS_BIT TRISAbits.TRISA10
#define RST_LAT_BIT LATAbits.LATA10
// Definitions for RS line
#define RS_TRIS_BIT AD1PCFGbits.PCFG10 = 1, TRISBbits.TRISB10
#define RS_LAT_BIT LATBbits.LATB10
// Definitions for CS line
#define CS_TRIS_BIT TRISGbits.TRISG13
#define CS_LAT_BIT LATGbits.LATG13
#define SetWaitDirection() //(PORTSetPinsDigitalIn(IOPORT_B, BIT_15))
#define WaitDataTx() //while(!PORTReadBits(IOPORT_B, BIT_15))
#elif defined (PIC24FJ256DA210_DEV_BOARD)
// Definitions for DISPLAY POWER ON pin
#define POWERON_LAT_BIT LATAbits.LATA5
#define POWERON_TRIS_BIT TRISAbits.TRISA5
#if defined (GFX_EPMP_CS1_BASE_ADDRESS)
#define EPMPCS1_CS_POLARITY GFX_ACTIVE_LOW
#define EPMPCS1_WR_POLARITY GFX_ACTIVE_LOW
#define EPMPCS1_RD_POLARITY GFX_ACTIVE_LOW
#define EPMPCS1_BE_POLARITY GFX_ACTIVE_LOW
// macros to define the access timing of the parallel device in EPMP CS1
#define EPMPCS1_DWAITB 0 // chip select 1 data set up before read/write strobe
#define EPMPCS1_DWAITM 0 // chip select 1 read/write strobe wait states
#define EPMPCS1_DWAITE 0 // chip select 1 data hold after read/write strobe
#define EPMPCS1_AMWAIT 0 // chip select 1 Alternate Master wait state
#endif
#if defined (GFX_EPMP_CS2_BASE_ADDRESS)
#define EPMPCS2_CS_POLARITY GFX_ACTIVE_LOW
#define EPMPCS2_WR_POLARITY GFX_ACTIVE_LOW
#define EPMPCS2_RD_POLARITY GFX_ACTIVE_LOW
#define EPMPCS2_BE_POLARITY GFX_ACTIVE_LOW
// macros to define the access timing of the parallel device in EPMP CS2
#define EPMPCS2_DWAITB 0 // chip select 2 data set up before read/write strobe
#define EPMPCS2_DWAITM 4 // chip select 2 read/write strobe wait states
#define EPMPCS2_DWAITE 0 // chip select 2 data hold after read/write strobe
#define EPMPCS2_AMWAIT 3 // chip select 2 Alternate Master wait state
#endif
#endif // defined (GFX_PICTAIL_V1)...
/*********************************************************************
* IO FOR THE BEEPER
*********************************************************************/
#if defined (GFX_PICTAIL_V2) || defined (GFX_PICTAIL_V1)
#if defined(__dsPIC33FJ128GP804__) || defined(__PIC24HJ128GP504__)
#define BEEP_TRIS_BIT TRISBbits.TRISB4
#define BEEP_LAT_BIT LATBbits.LATB4
#else
#define BEEP_TRIS_BIT TRISDbits.TRISD0
#define BEEP_LAT_BIT LATDbits.LATD0
#endif
#elif defined (GFX_PICTAIL_V3) || defined (PIC24FJ256DA210_DEV_BOARD)
#define BEEP_TRIS_BIT TRISDbits.TRISD0
#define BEEP_LAT_BIT LATDbits.LATD0
#endif // #if defined (GFX_PICTAIL_V2)
/*********************************************************************
* IOS FOR THE FLASH/EEPROM SPI
*********************************************************************/
#if defined (GFX_PICTAIL_V2) || defined (GFX_PICTAIL_V1)
#define USE_SST25_SPI2
#if defined(__PIC24F__) || defined(__PIC24H__) || defined(__dsPIC33F__)
#if defined(__dsPIC33FJ128GP804__) || defined(__PIC24HJ128GP504__)
#define EEPROM_CS_TRIS TRISAbits.TRISA0
#define EEPROM_CS_LAT LATAbits.LATA0
#elif defined(__PIC24FJ256GB110__)
// This PIM has RD12 rerouted to RG0
#define EEPROM_CS_TRIS TRISGbits.TRISG0
#define EEPROM_CS_LAT LATGbits.LATG0
#else
#define EEPROM_CS_TRIS TRISDbits.TRISD12
#define EEPROM_CS_LAT LATDbits.LATD12
#endif
#elif defined(__PIC32MX__)
#define EEPROM_CS_TRIS TRISDbits.TRISD12
#define EEPROM_CS_LAT LATDbits.LATD12
#endif
#if defined(__dsPIC33FJ128GP804__) || defined(__PIC24HJ128GP504__)
#define EEPROM_SCK_TRIS TRISCbits.TRISC2
#define EEPROM_SDO_TRIS TRISCbits.TRISC0
#define EEPROM_SDI_TRIS TRISCbits.TRISC1
#else
#define EEPROM_SCK_TRIS TRISGbits.TRISG6
#define EEPROM_SDO_TRIS TRISGbits.TRISG8
#define EEPROM_SDI_TRIS TRISGbits.TRISG7
#endif
#elif defined (GFX_PICTAIL_V3)
#define USE_SST25_SPI2
#if defined(__dsPIC33FJ128GP804__) || defined(__PIC24HJ128GP504__)
#define SST25_CS_TRIS TRISAbits.TRISA8
#define SST25_CS_LAT LATAbits.LATA8
#define SST25_SCK_TRIS TRISCbits.TRISC2
#define SST25_SDO_TRIS TRISCbits.TRISC0
#define SST25_SDI_TRIS TRISCbits.TRISC1
#else
#define SST25_CS_TRIS TRISDbits.TRISD1
#define SST25_CS_LAT LATDbits.LATD1
#define SST25_SCK_TRIS TRISGbits.TRISG6
#define SST25_SDO_TRIS TRISGbits.TRISG8
#define SST25_SDI_TRIS TRISGbits.TRISG7
#define SST25_SDI_ANS ANSGbits.ANSG7
#endif
#elif defined (PIC24FJ256DA210_DEV_BOARD)
#define USE_SST25_SPI2
#define SST25_CS_TRIS TRISAbits.TRISA14
#define SST25_CS_LAT LATAbits.LATA14
#define SST25_SCK_TRIS TRISDbits.TRISD8
#define SST25_SDO_TRIS TRISBbits.TRISB1
#define SST25_SDI_TRIS TRISBbits.TRISB0
#define SST25_SDI_ANS ANSBbits.ANSB0
#define SST25_SDO_ANS ANSBbits.ANSB1
#elif defined (MULTI_MEDIA_BOARD_DM00123)
#if defined (PIC32_GP_SK_DM320001) || defined (PIC32_USB_SK_DM320003_1)
#define USE_SST25_SPI2
#elif defined (PIC32_USB_SK_DM320003_2)
#define USE_SST25_SPI2A
#elif defined (PIC32_ENET_SK_DM320004)
#define USE_SST25_SPI3A
#else
#error "Please define the starter kit that you are using"
#endif
// define the CPLD SPI selection and chip select
#ifdef USE_SST25_SPI2
#define SST25_CS_TRIS TRISGbits.TRISG9
#define SST25_CS_LAT LATGbits.LATG9
#define SPI_FLASH_CHANNEL CPLD_SPI2
#elif defined (USE_SST25_SPI2A)
#define SST25_CS_TRIS TRISGbits.TRISG9
#define SST25_CS_LAT LATGbits.LATG9
#define SPI_FLASH_CHANNEL CPLD_SPI2A
#elif defined (USE_SST25_SPI3A)
#define SST25_CS_TRIS TRISFbits.TRISF12
#define SST25_CS_LAT LATFbits.LATF12
#define SPI_FLASH_CHANNEL CPLD_SPI3A
#else
#error "SPI Channel can't be used for SPI Flash"
#endif
#endif
/*********************************************************************
* IOS FOR THE GRAPHICS PICTAIL PARALLEL FLASH MEMORY
*********************************************************************/
#if defined (GFX_PICTAIL_V1)
#define SST39_CS_TRIS TRISDbits.TRISD9
#define SST39_CS_LAT LATDbits.LATD9
#define SST39_A18_TRIS TRISBbits.TRISB11
#define SST39_A18_LAT LATBbits.LATB11
#define SST39_A17_TRIS TRISBbits.TRISB10
#define SST39_A17_LAT LATBbits.LATB10
#define SST39_A16_TRIS TRISDbits.TRISD3
#define SST39_A16_LAT LATDbits.LATD3
#elif defined(GFX_PICTAIL_V2)
#if defined(__dsPIC33FJ128GP804__) || defined(__PIC24HJ128GP504__)
#define SST39_CS_TRIS TRISAbits.TRISA8
#define SST39_CS_LAT LATAbits.LATA8
#define SST39_A18_TRIS TRISAbits.TRISA1
#define SST39_A18_LAT LATAbits.LATA1
#define SST39_A17_TRIS TRISCbits.TRISC5
#define SST39_A17_LAT LATCbits.LATC5
#define SST39_A16_TRIS TRISCbits.TRISC4
#define SST39_A16_LAT LATCbits.LATC4
#else
#define SST39_CS_TRIS TRISDbits.TRISD1
#define SST39_CS_LAT LATDbits.LATD1
#define SST39_A18_TRIS TRISCbits.TRISC2
#define SST39_A18_LAT LATCbits.LATC2
#define SST39_A17_TRIS TRISGbits.TRISG15
#define SST39_A17_LAT LATGbits.LATG15
#define SST39_A16_TRIS TRISGbits.TRISG14
#define SST39_A16_LAT LATGbits.LATG14
#endif
#endif
/*********************************************************************
* IOS FOR THE TOUCH SCREEN
*********************************************************************/
// ADC Status
#define TOUCH_ADC_DONE AD1CON1bits.DONE
// ADC channel constants
#if defined (PIC24FJ256DA210_DEV_BOARD)
#define ADC_TEMP 4
#define ADC_POT 5
#elif defined (MULTI_MEDIA_BOARD_DM00123)
/* The Multi-Media Development Board does not have a
* analog pot or temperature sensor (see BMA150 for temperature
* sensor data
*/
#else
#if defined(__dsPIC33FJ128GP804__) || defined(__PIC24HJ128GP504__)
#define ADC_TEMP 4
#define ADC_POT 0
#define ADC_POT_TRIS TRISAbits.TRISA0
#define ADC_POT_PCFG AD1PCFGLbits.PCFG0
#elif defined(__PIC32MX__)
#define ADC_TEMP ADC_CH0_POS_SAMPLEA_AN4
#define ADC_POT ADC_CH0_POS_SAMPLEA_AN5
#else
#define ADC_TEMP 4
#define ADC_POT 5
#endif
#endif
#if defined (GFX_PICTAIL_V1)
#ifdef __PIC32MX__
#define ADC_XPOS ADC_CH0_POS_SAMPLEA_AN13
#define ADC_YPOS ADC_CH0_POS_SAMPLEA_AN12
#else
#define ADC_XPOS 13
#define ADC_YPOS 12
#endif
// Y port definitions
#define ADPCFG_XPOS AD1PCFGbits.PCFG13
#define LAT_XPOS LATBbits.LATB13
#define LAT_XNEG LATBbits.LATB11
#define TRIS_XPOS TRISBbits.TRISB13
#define TRIS_XNEG TRISBbits.TRISB11
// X port definitions
#define ADPCFG_YPOS AD1PCFGbits.PCFG12
#define LAT_YPOS LATBbits.LATB12
#define LAT_YNEG LATBbits.LATB10
#define TRIS_YPOS TRISBbits.TRISB12
#define TRIS_YNEG TRISBbits.TRISB10
#elif defined (GFX_PICTAIL_V2)
#if defined(__dsPIC33FJ128GP804__) || defined(__PIC24HJ128GP504__)
#define ADC_XPOS 5
#define ADC_YPOS 4
#elif defined(__PIC32MX__)
#define ADC_XPOS ADC_CH0_POS_SAMPLEA_AN11
#define ADC_YPOS ADC_CH0_POS_SAMPLEA_AN10
#else
#define ADC_XPOS 11
#define ADC_YPOS 10
#endif
#if defined(__dsPIC33FJ128GP804__) || defined(__PIC24HJ128GP504__)
// Y port definitions
#define ADPCFG_XPOS AD1PCFGLbits.PCFG5
#define LAT_XPOS LATBbits.LATB3
#define LAT_XNEG LATCbits.LATC9
#define TRIS_XPOS TRISBbits.TRISB3
#define TRIS_XNEG TRISCbits.TRISC9
// X port definitions
#define ADPCFG_YPOS AD1PCFGLbits.PCFG4
#define LAT_YPOS LATBbits.LATB2
#define LAT_YNEG LATCbits.LATC8
#define TRIS_YPOS TRISBbits.TRISB2
#define TRIS_YNEG TRISCbits.TRISC8
#else
// Y port definitions
#define ADPCFG_XPOS AD1PCFGbits.PCFG11
#define LAT_XPOS LATBbits.LATB11
#define LAT_XNEG LATGbits.LATG13
#define TRIS_XPOS TRISBbits.TRISB11
#define TRIS_XNEG TRISGbits.TRISG13
// X port definitions
#define ADPCFG_YPOS AD1PCFGbits.PCFG10
#define LAT_YPOS LATBbits.LATB10
#define LAT_YNEG LATGbits.LATG12
#define TRIS_YPOS TRISBbits.TRISB10
#define TRIS_YNEG TRISGbits.TRISG12
#endif
#elif defined (GFX_PICTAIL_V3)
#if defined(__dsPIC33FJ128GP804__) || defined(__PIC24HJ128GP504__)
#define ADC_XPOS 5
#define ADC_YPOS 4
#elif defined(__PIC32MX__)
#define ADC_XPOS ADC_CH0_POS_SAMPLEA_AN11
#define ADC_YPOS ADC_CH0_POS_SAMPLEA_AN10
#else
#define ADC_XPOS 11
#define ADC_YPOS 10
#endif
#if defined(__dsPIC33FJ128GP804__) || defined(__PIC24HJ128GP504__)
// Y port definitions
#define ADPCFG_XPOS AD1PCFGLbits.PCFG5
#define LAT_XPOS LATBbits.LATB3
#define LAT_XNEG LATCbits.LATC9
#define TRIS_XPOS TRISBbits.TRISB3
#define TRIS_XNEG TRISCbits.TRISC9
// X port definitions
#define ADPCFG_YPOS AD1PCFGLbits.PCFG4
#define LAT_YPOS LATBbits.LATB2
#define LAT_YNEG LATCbits.LATC8
#define TRIS_YPOS TRISBbits.TRISB2
#define TRIS_YNEG TRISCbits.TRISC8
#else
// Y port definitions
#define ADPCFG_XPOS AD1PCFGbits.PCFG11
#define LAT_XPOS LATBbits.LATB11
#define TRIS_XPOS TRISBbits.TRISB11
#if defined(__32MX460F512L__) && !defined (PIC32_USB_SK_DM320003_1)
#define LAT_XNEG LATGbits.LATG15
#define TRIS_XNEG TRISGbits.TRISG15
#else
#define LAT_XNEG LATDbits.LATD9
#define TRIS_XNEG TRISDbits.TRISD9
#endif
// X port definitions
#define ADPCFG_YPOS AD1PCFGbits.PCFG10
#define LAT_YPOS LATBbits.LATB10
#define LAT_YNEG LATDbits.LATD8
#define TRIS_YPOS TRISBbits.TRISB10
#define TRIS_YNEG TRISDbits.TRISD8
#endif
#elif defined (PIC24FJ256DA210_DEV_BOARD)
#if defined(__PIC24FJ256DA210__)
#define ADC_XPOS 16
#define ADC_YPOS 18
// Y port definitions
#define ADPCFG_XPOS ANSCbits.ANSC4
#define LAT_XPOS LATCbits.LATC4
#define TRIS_XPOS TRISCbits.TRISC4
#define LAT_XNEG LATAbits.LATA2
#define TRIS_XNEG TRISAbits.TRISA2
// X port definitions
#define ADPCFG_YPOS ANSGbits.ANSG7
#define LAT_YPOS LATGbits.LATG7
#define TRIS_YPOS TRISGbits.TRISG7
#define LAT_YNEG LATAbits.LATA1
#define TRIS_YNEG TRISAbits.TRISA1
#endif
#elif defined (MULTI_MEDIA_BOARD_DM00123)
#define ADC_XPOS ADC_CH0_POS_SAMPLEA_AN11
#define ADC_YPOS ADC_CH0_POS_SAMPLEA_AN14
// X port definitions
#define ADPCFG_XPOS AD1PCFGbits.PCFG11
#define LAT_XPOS LATBbits.LATB11
#define TRIS_XPOS TRISBbits.TRISB11
#define LAT_XNEG LATBbits.LATB13
#define TRIS_XNEG AD1PCFGbits.PCFG13 = 1, TRISBbits.TRISB13
// Y port definitions
#define ADPCFG_YPOS AD1PCFGbits.PCFG14
#define LAT_YPOS LATBbits.LATB14
#define TRIS_YPOS TRISBbits.TRISB14
#define LAT_YNEG LATBbits.LATB12
#define TRIS_YNEG AD1PCFGbits.PCFG12 = 1, TRISBbits.TRISB12
#endif
/*********************************************************************
* IOS FOR THE SWITCHES (SIDE BUTTONS)
*********************************************************************/
#if defined (PIC24FJ256DA210_DEV_BOARD)
#if defined(__PIC24FJ256DA210__)
#define BTN_S1 _RG8
#define BTN_S2 _RE9
#define BTN_S3 _RB5
#endif
#elif defined (MULTI_MEDIA_BOARD_DM00123)
#define BTN_S3 1
#define BTN_S4 1
#define BTN_S5 1
#define BTN_S6 1
#else
#if defined(__dsPIC33FJ128GP804__) || defined(__PIC24HJ128GP504__)
#define BTN_S3 _RA9
#define BTN_S4 1
#define BTN_S5 1
#define BTN_S6 1
#elif defined (PIC32_USB_SK_DM320003_1) || defined (PIC32_USB_SK_DM320003_2) || defined (PIC32_GP_SK_DM320001)
#define BTN_S3 1
#define BTN_S4 1
#define BTN_S5 1
#define BTN_S6 1
#else
#define BTN_S3 _RD6
#define BTN_S4 _RD13
#define BTN_S5 _RA7
#define BTN_S6 _RD7
#endif
#endif
/*********************************************************************
* IOS FOR THE TCON
*********************************************************************/
#if defined (PIC24FJ256DA210_DEV_BOARD)
#if (DISPLAY_PANEL == TFT_G240320LTSW_118W_E)
#define CS_PORT _RA0
#define CS_TRIS _TRISA0
#define CS_DIG()
#define SCL_PORT _RD8
#define SCL_TRIS _TRISD8
#define SCL_DIG()
#define SDO_PORT _RB1
#define SDO_TRIS _TRISB1
#define SDO_DIG() _ANSB1 = 0;
#define DC_PORT _RB0
#define DC_TRIS _TRISB0
#define DC_DIG() _ANSB0 = 0;
#endif // #if (DISPLAY_PANEL == TFT_G240320LTSW_118W_E)
#endif // #if defined (DA210_DEV_BOARD)...
#endif //ifdef _GRAPHICS_H
/*********************************************************************
* IOS FOR THE UART
*********************************************************************/
#if defined(__dsPIC33FJ128GP804__) || defined(__PIC24HJ128GP504__)
#define TX_TRIS TRISCbits.TRISC1
#define RX_TRIS TRISCbits.TRISC0
#elif defined(__PIC24FJ256DA210__)
#define TX_TRIS TRISFbits.TRISF3
#define RX_TRIS TRISDbits.TRISD0
#else
#define TX_TRIS TRISFbits.TRISF5
#define RX_TRIS TRISFbits.TRISF4
#endif
/*********************************************************************
* RTCC DEFAULT INITIALIZATION (these are values to initialize the RTCC
*********************************************************************/
#define RTCC_DEFAULT_DAY 29 // 29
#define RTCC_DEFAULT_MONTH 4 // April
#define RTCC_DEFAULT_YEAR 10 // 2010
#define RTCC_DEFAULT_WEEKDAY 04 // Thursday
#define RTCC_DEFAULT_HOUR 10 // 10:10:01
#define RTCC_DEFAULT_MINUTE 10
#define RTCC_DEFAULT_SECOND 01
#if defined (MULTI_MEDIA_BOARD_DM00123)
#include
/*********************************************************************
* Configuration for the CPLD
*********************************************************************/
#ifdef USE_16BIT_PMP
#define GRAPHICS_HW_CONFIG CPLD_GFX_CONFIG_16BIT
#else
#define GRAPHICS_HW_CONFIG CPLD_GFX_CONFIG_8BIT
#endif
/*********************************************************************
* MMB LEDs
*********************************************************************/
typedef enum
{
LED_2,
LED_3,
LED_4,
LED_5,
LED_10
}MMB_LED;
extern inline void __attribute__((always_inline)) SetLEDDirection(void)
{
PORTSetPinsDigitalOut(IOPORT_D, (BIT_1 | BIT_2 | BIT_3));
PORTSetPinsDigitalOut(IOPORT_C, (BIT_1 | BIT_2));
}
extern inline void __attribute__((always_inline)) TurnLEDOn(MMB_LED led)
{
if(led == LED_2)
PORTSetBits(IOPORT_D, BIT_1);
if(led == LED_3)
PORTSetBits(IOPORT_D, BIT_2);
if(led == LED_4)
PORTSetBits(IOPORT_D, BIT_3);
if(led == LED_5)
PORTSetBits(IOPORT_C, BIT_1);
if(led == LED_10)
PORTSetBits(IOPORT_C, BIT_2);
}
extern inline void __attribute__((always_inline)) TurnLEDOff(MMB_LED led)
{
if(led == LED_2)
PORTClearBits(IOPORT_D, BIT_1);
if(led == LED_3)
PORTClearBits(IOPORT_D, BIT_2);
if(led == LED_4)
PORTClearBits(IOPORT_D, BIT_3);
if(led == LED_5)
PORTClearBits(IOPORT_C, BIT_1);
if(led == LED_10)
PORTClearBits(IOPORT_C, BIT_2);
}
extern inline void __attribute__((always_inline)) ToggleLED(MMB_LED led)
{
if(led == LED_2)
PORTToggleBits(IOPORT_D, BIT_1);
if(led == LED_3)
PORTToggleBits(IOPORT_D, BIT_2);
if(led == LED_4)
PORTToggleBits(IOPORT_D, BIT_3);
if(led == LED_5)
PORTToggleBits(IOPORT_C, BIT_1);
if(led == LED_10)
PORTToggleBits(IOPORT_C, BIT_2);
}
extern inline void __attribute__((always_inline)) TurnLEDAllOn(void)
{
PORTSetBits(IOPORT_D, BIT_1);
PORTSetBits(IOPORT_D, BIT_2);
PORTSetBits(IOPORT_D, BIT_3);
PORTSetBits(IOPORT_C, BIT_1);
PORTSetBits(IOPORT_C, BIT_2);
}
extern inline void __attribute__((always_inline)) TurnLEDAllOff(void)
{
PORTClearBits(IOPORT_D, BIT_1);
PORTClearBits(IOPORT_D, BIT_2);
PORTClearBits(IOPORT_D, BIT_3);
PORTClearBits(IOPORT_C, BIT_1);
PORTClearBits(IOPORT_C, BIT_2);
}
#endif // #ifdef (MULTI_MEDIA_BOARD_DM00123)
#endif // __HARDWARE_PROFILE_H