// PIC18F8722 Configuration Bit Settings
// 'C' source line config statements
#include <xc.h>
// #pragma config statements should precede project file includes.
// Use project enums instead of #define for ON and OFF.
// CONFIG1H
#pragma config OSC = INTIO67 // Oscillator Selection bits (Internal oscillator block, port function on RA6 and RA7)
#pragma config FCMEN = OFF // Fail-Safe Clock Monitor Enable bit (Fail-Safe Clock Monitor disabled)
#pragma config IESO = OFF // Internal/External Oscillator Switchover bit (Two-Speed Start-up disabled)
// CONFIG2L
#pragma config PWRT = OFF // Power-up Timer Enable bit (PWRT disabled)
#pragma config BOREN = ON // Brown-out Reset Enable bits (Brown-out Reset enabled and controlled by software (SBOREN is enabled))
#pragma config BORV = 3 // Brown-out Voltage bits (Minimum setting)
// CONFIG2H
#pragma config WDT = OFF // Watchdog Timer (WDT disabled (control is placed on the SWDTEN bit))
#pragma config WDTPS = 32768 // Watchdog Timer Postscale Select bits (1:32768)
// CONFIG3L
#pragma config MODE = MC // Processor Data Memory Mode Select bits (Microcontroller mode)
#pragma config ADDRBW = ADDR20BIT// Address Bus Width Select bits (20-bit Address Bus)
#pragma config DATABW = DATA16BIT// Data Bus Width Select bit (16-bit External Bus mode)
#pragma config WAIT = OFF // External Bus Data Wait Enable bit (Wait selections are unavailable for table reads and table writes)
// CONFIG3H
#pragma config CCP2MX = PORTC // CCP2 MUX bit (ECCP2 input/output is multiplexed with RC1)
#pragma config ECCPMX = PORTE // ECCP MUX bit (ECCP1/3 (P1B/P1C/P3B/P3C) are multiplexed onto RE6, RE5, RE4 and RE3 respectively)
#pragma config LPT1OSC = OFF // Low-Power Timer1 Oscillator Enable bit (Timer1 configured for higher power operation)
#pragma config MCLRE = OFF // MCLR Pin Enable bit (RG5 input pin enabled; MCLR disabled)
// CONFIG4L
#pragma config STVREN = ON // Stack Full/Underflow Reset Enable bit (Stack full/underflow will cause Reset)
#pragma config LVP = OFF // Single-Supply ICSP Enable bit (Single-Supply ICSP disabled)
#pragma config BBSIZ = BB2K // Boot Block Size Select bits (1K word (2 Kbytes) Boot Block size)
#pragma config XINST = OFF // Extended Instruction Set Enable bit (Instruction set extension and Indexed Addressing mode disabled (Legacy mode))
// CONFIG5L
#pragma config CP0 = OFF // Code Protection bit Block 0 (Block 0 (000800, 001000 or 002000-003FFFh) not code-protected)
#pragma config CP1 = OFF // Code Protection bit Block 1 (Block 1 (004000-007FFFh) not code-protected)
#pragma config CP2 = OFF // Code Protection bit Block 2 (Block 2 (008000-00BFFFh) not code-protected)
#pragma config CP3 = OFF // Code Protection bit Block 3 (Block 3 (00C000-00FFFFh) not code-protected)
#pragma config CP4 = OFF // Code Protection bit Block 4 (Block 4 (010000-013FFFh) not code-protected)
#pragma config CP5 = OFF // Code Protection bit Block 5 (Block 5 (014000-017FFFh) not code-protected)
#pragma config CP6 = OFF // Code Protection bit Block 6 (Block 6 (01BFFF-018000h) not code-protected)
#pragma config CP7 = OFF // Code Protection bit Block 7 (Block 7 (01C000-01FFFFh) not code-protected)
// CONFIG5H
#pragma config CPB = OFF // Boot Block Code Protection bit (Boot Block (000000-0007FFh) not code-protected)
#pragma config CPD = OFF // Data EEPROM Code Protection bit (Data EEPROM not code-protected)
// CONFIG6L
#pragma config WRT0 = OFF // Write Protection bit Block 0 (Block 0 (000800, 001000 or 002000-003FFFh) not write-protected)
#pragma config WRT1 = OFF // Write Protection bit Block 1 (Block 1 (004000-007FFFh) not write-protected)
#pragma config WRT2 = OFF // Write Protection bit Block 2 (Block 2 (008000-00BFFFh) not write-protected)
#pragma config WRT3 = OFF // Write Protection bit Block 3 (Block 3 (00C000-00FFFFh) not write-protected)
#pragma config WRT4 = OFF // Write Protection bit Block 4 (Block 4 (010000-013FFFh) not write-protected)
#pragma config WRT5 = OFF // Write Protection bit Block 5 (Block 5 (014000-017FFFh) not write-protected)
#pragma config WRT6 = OFF // Write Protection bit Block 6 (Block 6 (01BFFF-018000h) not write-protected)
#pragma config WRT7 = OFF // Write Protection bit Block 7 (Block 7 (01C000-01FFFFh) not write-protected)
// CONFIG6H
#pragma config WRTC = OFF // Configuration Register Write Protection bit (Configuration registers (300000-3000FFh) not write-protected)
#pragma config WRTB = OFF // Boot Block Write Protection bit (Boot Block (000000-007FFF, 000FFF or 001FFFh) not write-protected)
#pragma config WRTD = OFF // Data EEPROM Write Protection bit (Data EEPROM not write-protected)
// CONFIG7L
#pragma config EBTR0 = OFF // Table Read Protection bit Block 0 (Block 0 (000800, 001000 or 002000-003FFFh) not protected from table reads executed in other blocks)
#pragma config EBTR1 = OFF // Table Read Protection bit Block 1 (Block 1 (004000-007FFFh) not protected from table reads executed in other blocks)
#pragma config EBTR2 = OFF // Table Read Protection bit Block 2 (Block 2 (008000-00BFFFh) not protected from table reads executed in other blocks)
#pragma config EBTR3 = OFF // Table Read Protection bit Block 3 (Block 3 (00C000-00FFFFh) not protected from table reads executed in other blocks)
#pragma config EBTR4 = OFF // Table Read Protection bit Block 4 (Block 4 (010000-013FFFh) not protected from table reads executed in other blocks)
#pragma config EBTR5 = OFF // Table Read Protection bit Block 5 (Block 5 (014000-017FFFh) not protected from table reads executed in other blocks)
#pragma config EBTR6 = OFF // Table Read Protection bit Block 6 (Block 6 (018000-01BFFFh) not protected from table reads executed in other blocks)
#pragma config EBTR7 = OFF // Table Read Protection bit Block 7 (Block 7 (01C000-01FFFFh) not protected from table reads executed in other blocks)
// CONFIG7H
#pragma config EBTRB = OFF // Boot Block Table Read Protection bit (Boot Block (000000-007FFF, 000FFF or 001FFFh) not protected from table reads executed in other blocks)
void main (void)
{
while(1)
{
}
}
